Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Repair Nationwide
A gate that won’t open is more than a nuisance. It blocks your car, leaves your property exposed, or locks you out completely. Gate repair is the diagnostic and corrective work that restores a driveway gate, automatic opener, or gate motor to proper function. Warden Gate Repair has specialized in exactly this since 2008, as part of the Threshold Group family. We’re the gate-and-opener specialist that removes the two biggest worries in home service: not knowing who is coming to your door and not knowing what it will cost. Before dispatch, we send you the technician’s name and photo. Before any work begins, we hand you a written price. And every repair is backed by the 365-Day Done Right Promise. If the repair isn’t right, we return free and make it right. Live phone support is available 24/7 at (828) 426-7081.
Driveway Gate Repair
Driveway Gate Repair covers every mechanical and electrical fault that keeps a residential driveway gate from opening, closing, or latching as designed. You need it when the gate grinds, sags, reverses mid-travel, or stops responding to remotes and keypads. Warden Gate Repair sends a named, background-checked technician who diagnoses the problem and hands you a written price before any work starts. Expect most driveway gate jobs to land between $250 and $650 depending on the fault, the gate motor involved, and the parts required-see our Gate Repair pricing for more detail.
Common Swing Gate Faults
Hinge wear is the leading cause of a sagging driveway gate. The second is a gate motor that has slipped out of alignment. We replace hinges, re-set motor mounts, and re-level the gate leaf so the opener isn’t fighting the gate’s own weight.
Driveway Gate Operator Diagnosis
When a gate won’t move at all, the problem is usually the operator, not the gate. That means the circuit board, capacitor, limit switch, or receiver inside the gate motor. We bench-test the operator on site, identify the failed component, and quote the exact repair before ordering a single part.
Gate Welding
Gate Welding is the structural repair method used when a gate’s metal frame has cracked, a hinge has torn loose, or a section has rusted through. It is needed after storm damage, vehicle impact, or years of stress on a steel or iron gate. Warden Gate Repair performs on-site welding with mobile equipment, so the gate stays in place and the repair is measured against the actual load. Typical gate welding work runs $300 to $800, influenced by crack length, metal thickness, and whether we need to cut out and replace a section rather than simply re-weld it.
Crack Repair and Reinforcement
A cracked tube gate usually cracks again if you only weld the visible line. We grind the area clean, weld the crack, then add a reinforcing plate or gusset where the stress concentrates. That is the difference between a repair that lasts and one that fails in a year.
Hinge and Post Restoration
When a hinge tears off a steel post, the post itself often needs rebuilding at the attachment point. We weld a new hinge plate to the post, re-align the gate, and verify the weld with a load test before we leave.
Commercial Gate Repair
Commercial Gate Repair is the service category for gates on business properties, industrial lots, apartment communities, and managed facilities. These gates run more cycles per day than a residential gate runs in a month, so wear shows up faster. They also carry liability: a gate that reverses onto a vehicle creates a claim. Warden Gate Repair works on commercial operators and barrier gates with factory-trained technicians who carry the right parts for DoorKing, LiftMaster, and Elite systems-read Choosing the Right Gate Repair Brand: A Buyer’s Guide for Los Angeles to understand how we select equipment. Commercial gate repair typically runs $400 to $1,200 per service call, depending on operator type, access control integration, and parts.
High-Cycle Operator Wear
Commercial slide and swing operators burn through limit switches, drive belts, and capacitors faster than residential units. We inspect the full drive train and replace worn components before they take the gate offline during business hours.
Access Control Integration
Most commercial gates tie into keypads, card readers, or telephone entry systems. When the gate fails, it’s often the control wiring or a relay, not the gate itself. We trace the signal path from the reader to the operator and repair the actual fault, without replacing equipment that still works.
Iron Gate Repair
Iron Gate Repair addresses the structural and cosmetic damage common on solid and ornamental iron gates. Iron is heavy and rigid, which makes it strong and also vulnerable to cracking at the welds and rusting at the joints. You need it when you see rust bloom along the bottom rail, cracks at the hinge mounts, or a gate that scrapes the ground. Warden Gate Repair handles straightening, weld repair, rust treatment, and hinge or latch replacement on iron gates of every design. Ballpark pricing for iron gate repair is $300 to $800, depending on damage scope and whether sections must be cut out and replaced.
Rust Remediation and Prevention
Iron gates rust from the inside of the tubes out. By the time you see rust staining, the section usually needs grinding, treatment, and repainting, not just a coat of paint over the top. We remove the rust, treat the bare metal, and prime before finishing.
Weld and Hinge Renewal
Iron gates are almost always hung on welded hinges. When those welds crack, the gate drops and the opener labors. We grind out the failed weld, re-weld the hinge while the gate is supported and level, and test the swing path several times before the job closes.
Sliding Gate Repair
Sliding Gate Repair covers the track, rollers, chain, and motor on horizontal slide gates, both cantilever and track-mounted. These gates fail differently than swing gates: the common faults are debris in the track, worn rollers, a stretched chain, or a motor that has lost its limit settings. You need sliding gate repair when the gate shudders while moving, stalls halfway, or grinds loudly near the end of travel. Warden Gate Repair services slide gates from Viking, Linear, and Ghost Controls, among others, as part of our Gate Repair in Los Angeles. Most sliding gate repairs run $300 to $750.
Track and Roller Service
A gate that shudders or hops while opening usually has a flat-spotted roller or a track full of gravel. We clean the track, replace worn rollers, and re-align the gate so it rolls straight without dragging the frame against the post.
Chain and Limit Switch Adjustments
When a slide gate stops short or over-travels, the limit switches or the chain tension are usually at fault. We re-set the travel limits to the manufacturer’s spec and tension the chain so the motor isn’t springing slack every time it starts.
Wrought Iron Gate Repair
Wrought Iron Gate Repair is the specialized restoration of ornamental gates made from traditional wrought iron or modern mild steel in the wrought style. These gates have pickets, scrolls, and finials that complicate structural repairs. Damaged scrollwork, cracked pickets, and failed welds at decorative joints are the typical calls. Warden Gate Repair has the mobile welding setup and the finishing experience to repair ornamental sections without butchering the gate’s look. Wrought iron gate repair generally falls between $350 and $900, with decorative scroll replacement at the upper end.
Scroll and Picket Replacement
When a picket snaps or a scroll rusts through, you can’t hide the repair. We fabricate a matching piece, weld it in cleanly, and finish the area so the repair doesn’t glare at you every time you pull in.
Ornamental Weld Repair
Ornamental joints are narrow, and a clumsy weld destroys the pattern. We use the right rod size and heat control to fuse the joint without building up excess bead, then grind and finish the repair to match the surrounding metal.
Metal Gate Repair
Metal Gate Repair is the broad category for gates built from steel, aluminum, or mixed metal construction, including tube steel frame gates and aluminum residential driveway gates. The need shows up as a sag, a crack, a broken weld, or a latch that won’t hold. Since metal gates are built from hollow sections and welded corners, water gets in and rust works from the inside. Warden Gate Repair evaluates the gate’s structure, welds, hinges, and finish, then writes up a scope and price. Typical metal gate repair runs $250 to $700.
Steel Frame Sag Correction
A steel gate usually sags because a hinge weld has stretched or a corner joint has fatigued. We re-square the frame, add a brace if the design allows it, and re-hang the gate so the latch closes without lifting.
Aluminum Gate Repair
Aluminum gates crack more easily than steel but don’t rust. They need a different weld process and lighter finishing work. We handle aluminum gate welding and hinge replacement with the correct filler material so the repair holds instead of cracking beside the weld.
Wood Gate Repair
Wood Gate Repair covers sagging, rotting, and failed hardware on wooden driveway gates, side gates, and garden gates. The material matters: wood moves with moisture, rots at ground contact, and splits around fasteners. You need it when the gate drags, the posts lean, or the hinges pull out of the wood. Warden Gate Repair replaces rot, reinforces frames, installs anti-sag hardware, and re-sets leaning posts. Wood gate repair typically costs $200 to $600, depending on the amount of rot and whether the post footings need resetting.
Rot Repair and Frame Reinforcement
The bottom rail and post base are the first areas to rot. We cut out the damaged wood, splice in replacement stock, and add a steel corner brace or anti-sag kit so the frame holds its square shape.
Post Reset and Hardware Replacement
A leaning post ruins the gate’s swing path and strains the hinges. We dig out the old footing, set the post plumb in new concrete, and re-hang the gate with heavy-duty hinges sized for the gate’s actual weight.
Brands We Service
We’re factory-trained on DoorKing operators, which are common on commercial and multi-family sites across the country. We stock their OEM limit switches, control boards, and loop detectors, so most DoorKing repairs are completed on the first visit.
LiftMaster residential and commercial operators are the most common units we see, and we carry their receivers, wall stations, and safety edges. For Mighty Mule swing and slide openers, we know the battery, actuator, and solar wiring faults that dominate service calls. Whether you have one of these brands or any other make, we can help.
Signs You Need a Pro Right Now
- Your gate reverses or stops mid-travel. This usually means a dying safety sensor, a bad capacitor, or a limit switch drifting out of spec. A gate that reverses randomly is a vehicle damage risk and should be addressed the same week.
- The gate motor hums but the gate doesn’t move. The motor is getting power but the drive train isn’t engaging. That points to a failed capacitor, a stripped gear, or a broken chain, and running it this way can burn out the motor entirely.
- You hear grinding, banging, or a loud pop during operation. Noise means a mechanical part is making contact where it shouldn’t. Metal shavings under the operator or a jerky gate in motion mean a bearing, roller, or gear is failing.
- The gate sags and the latch won’t line up. A sagging gate is a structural problem, not just a cosmetic one. The opener has to work harder, hinges wear faster, and the gate can fail at the weld or hinge.
- Your keypad, remote, or intercom stopped working with the gate. When the access system fails, you can’t secure the property or let anyone in. Wiring faults and receiver failures are common and usually repairable without replacing the whole operator.
Our Process, Step by Step
- 1
You call and talk to a real person. A live human answers 24/7, not a voicemail or a chatbot. We take down the symptom, the gate type, and the opener brand if you know it.
- 2
You get the technician’s name and photo before arrival. Every Warden technician is background-checked, identity-verified, and photo-badged under our Threshold Standard. You’ll know exactly who is coming to your door before they get there.
- 3
We diagnose on site and hand you a written price. The technician tests the gate, the operator, the safety edges, and the wiring. Then you get a written quote before any work starts, with no surprise line items at the end.
- 4
You approve, and we repair. We carry common OEM parts for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Most repairs are finished on the same visit.
- 5
We walk you through the repair and your warranty. We demonstrate the gate working, explain what was replaced and why, and leave you with the written 365-Day Done Right Promise covering the job.
How Much Does Gate Repair Cost?
A typical driveway gate repair runs $250 to $650. Gate welding repairs generally fall between $300 and $800 depending on the crack’s length and location. Commercial gate repair runs higher, usually $400 to $1,200 per visit, because the operators are heavier and the access control integration adds variables. Wrought iron and ornamental work tends to run $350 to $900 when decorative scrolls or pickets need replacement. Wood gate repair is the most affordable category at $200 to $600.
What changes the price: the gate’s size and weight, whether the operator or just the mechanical hardware is at fault, parts availability for your brand, and whether welding or concrete work is required. The way to avoid overpaying is to get a written price before any work begins, which is how Warden operates on every job. Our estimates are free, and every repair quote lists parts, labor, and the warranty term in writing. Call (828) 426-7081 to schedule an estimate. You’ll know the number before you decide anything.
Where We Work
Warden Gate Repair serves homeowners and businesses across the United States through local crews, each independently owned and operated within the Threshold Group family. Every location follows the same Threshold Standard for technician vetting, badging, and written pricing. When you call, you’re connected with a live person who dispatches the right local crew for your area.
Frequently Asked Questions About Gate Repair
Gate repair is the diagnostic and corrective work that restores a driveway gate, automatic opener, or gate motor to proper function. It covers mechanical faults like sagging, cracked welds, and failed hinges, plus electrical faults in the operator, safety sensors, and access controls. For a full breakdown, see The Complete Electric Gate Repair Guide for Los Angeles Homeowners. Warden Gate Repair has specialized exclusively in this trade since 2008.
Most residential gate repairs are completed in one visit, typically within two to four hours once the technician is on site. We carry common OEM parts for the brands we service, which cuts out the wait for parts shipping. Larger structural repairs, like major welding or post resets, may take a half-day.
Residential gate repair typically runs $250 to $650, while welding and iron work ranges from $300 to $900. Commercial gate repair runs $400 to $1,200 depending on the operator and access controls. You’ll receive a written price before any work begins, and the estimate is free. Call (828) 426-7081 for an exact quote for your gate.
Yes. We are factory-trained on all three brands and carry their common OEM parts. LiftMaster residential operators, DoorKing commercial units, and Mighty Mule swing and slide openers are all within our regular service set. We also service FAAC, BFT, Linear, Viking, Ghost Controls, and Elite equipment.
Yes. Our live-person phone line is staffed 24 hours a day, 7 days a week, 365 days a year. If your gate is stuck open, stuck closed, or won’t secure the property, call (828) 426-7081 and we’ll dispatch the nearest available crew.
Every repair comes with the 365-Day Done Right Promise. If the repair isn’t right, we return and make it right, and the return visit is free. The warranty is written, not verbal, so you know exactly what is covered and for how long.
Clear vehicle access to the gate and make sure the gate has power if it’s an electric model. It helps if you know your opener’s brand and where the manual or remote is. You’ll receive the technician’s name and photo before arrival, and they’ll show a photo ID badge when they knock.
Schedule Your Gate Repair Service Today
Call (828) 426-7081 for a free estimate. You’ll talk to a live person, get a technician’s name and photo before dispatch, and receive a written price before any work starts. Every job is backed by the 365-Day Done Right Promise. We answer live 24/7, and no repair moves forward without your approval on the number.
Written by Cole Rafferty, Owner at Warden Gate Repair, serving customers nationwide since 2008.