Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Everman, TX
Gate repair in Everman, TX usually means one of two things: a sagging swing gate that won’t latch anymore, or an opener that hums but won’t move the gate. The sagging gate is far more common here, and it’s rarely the hinge’s fault. It’s the clay. Everman sits on some of the most aggressively shifting soil in Tarrant County, and gates set in shallow footings decades ago have been slowly tilting ever since. We reset posts, realign hinges, and rebuild frames so the gate actually closes and locks the way it should. If that’s what you’re dealing with, call us at (828) 426-7081 and we’ll walk you through it.
Why Everman Homes Are Different
Everman’s housing stock is mostly 1950s through 1980s ranch homes on compact lots, and a large share of them have chain-link perimeter fencing with basic swing gates. Those gates were often set in shallow concrete footings straight into the native clay. Over 30 or 40 years of North Texas wet-dry cycles, that clay expands and contracts enough to push posts 5 to 10 degrees out of plumb without any vehicle ever hitting them. The gate doesn’t sag because the hinges wore out. It sags because the post itself moved.
What we see in Everman more than anywhere else in the southern Metroplex is the slow heave and lean of gate posts. The summers pull moisture out and the winters put it back, and every cycle shifts the footing a little more. The repair call usually comes in as “my gate won’t close” but the real job is pulling the hinge post, digging a deeper hole, setting it with a gravel drainage collar so water doesn’t pool against the concrete, and then re-hanging the gate square. It’s more involved than a hinge swap, and it’s the fix that actually lasts in this soil.
Ice storms add a second layer. Everman catches the same freezing rain corridor that hits the rest of the DFW south suburbs, and older steel frames that have already rusted at the welds will crack under the added weight. We see snapped hinge welds and fractured top rails after almost every hard freeze. None of this is exotic work. It’s just work that has to account for local ground and local weather, and estimating it correctly is the difference between a gate that stays fixed and one that’s sagging again next spring.
Our Main Everman Services
Most Everman homeowners call us for one of three problems: a gate that won’t swing or latch properly, an electric gate that stopped responding to the opener, or a gate motor that runs but doesn’t move the gate. Each has its own Everman page with pricing and specifics below.
Gate Repair in Everman
Most gate repair in Everman starts with a leaning post or a hinge that’s been fighting the soil for years. We pull and reset posts in deeper footings with drainage, weld cracked frames, replace hinges, and adjust the latch so the gate closes square and stays closed. On chain-link gates we’re often matching the existing pipe size and replacing bent top rails at the same time. See what a typical Gate Repair in Everman job includes and what it runs.
Electric Gate Repair in Everman
Electric gates add wiring, control boards, photocells, and safety loops on top of the mechanical frame. In Everman the most common failure points are weathered junction boxes, corroded wire nuts, and photocells knocked out of alignment by a gate that’s already leaning. We trace the circuit, repair or replace the damaged component, and test the full open-close cycle before we leave. Details and pricing are on the Electric Gate Repair in Everman page.
Gate Motor Repair in Everman
A gate motor (the box that slides or swings your gate automatically) that runs without moving the gate is usually a stripped gear, a failed capacitor, or a broken drive arm. In Everman we also see motors working harder than they should because the gate itself is dragging on a shifted post, which burns out the motor early. We diagnose the mechanical drag first, then repair or replace the motor. See the Gate Motor Repair in Everman page for full scope and cost.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Everman
Our techs are factory-trained on the brands most common around Everman: FAAC and BFT hydraulic and electromechanical operators, Linear control boards, and Viking swing and slide operators. We keep common replacement parts on the truck for these lines, which means many Everman repairs are completed on the first visit. Full details are on our brands page.
Pricing for Gate Company in Everman, TX
| Service | Typical range in Everman |
|---|---|
| Service call / diagnostics | $59 – $99, waived with repair |
| Gate post reset (single post) | $275 – $600 |
| Gate post reset (double gate) | $500 – $1,100 |
| Hinge replacement (standard pair) | $120 – $300 |
| Gate frame welding repair | $150 – $400 per section |
| Latch / lock replacement | $90 – $250 |
| Gate opener installation (motor) | $725 – $1,800 |
| Control board replacement | $250 – $650 |
| Photocell / safety edge replacement | $150 – $400 per pair |
| Full gate replacement (basic chain-link) | $900 – $2,400 |
Prices in Everman push toward the higher end when a post has to be dug out of compromised clay and reset in a deeper footing, or when an old frame needs multiple weld repairs before it’s square again. Every Everman job gets a written price before any work starts, and that number doesn’t change at the end unless you approve it first.
Neighborhoods We Serve in Everman
We cover all of Everman, including the older ranch-home streets on the east side near Everman Joe C. Bean High School, the neighborhoods west of Everman Parkway, and the mixed residential pockets off Mitchell Boulevard. We also serve the newer subdivisions on the south and west edges of town. Standard response time anywhere in Everman is same-day or next-day for non-emergency calls.
- East Everman (near the high school)
- West Everman off Everman Parkway
- Mitchell Boulevard corridor
- South Everman subdivisions
Service Area – Cities Near Everman
Beyond Everman, Warden Gate Repair serves the greater DFW area and several other Texas and Florida locations. If you’re just outside Everman, our teams cover Fort Worth, TX and Dallas, TX directly. We also serve Houston, TX and San Antonio, FL for gates and openers in those markets.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Everman
Most Everman calls are scheduled same-day or next-day. Emergency calls for a gate stuck open or a security risk get priority, and our live phone line is answered 24/7. Call (828) 426-7081 and we’ll give you a real arrival window, not a vague “sometime this week.”
Most gate repairs and post resets don’t require a permit in Everman. Full replacements or anything involving new electrical runs may need city approval depending on scope. We’ll tell you during the estimate exactly what’s required, and we don’t start until you know.
We cover all of Everman plus Fort Worth, Dallas, and the surrounding south Tarrant County suburbs. Each city has its own local crews and scheduling. If you’re unsure whether you’re in our Everman area, call (828) 426-7081 and the person who answers will confirm it right there.
If your gate is sagging, stuck, or the opener’s given up, call Warden Gate Repair at (828) 426-7081. We’ll send a technician whose name and photo you get before we arrive, quote you a written price before any work begins, and stand behind the repair with the 365-Day Done Right Promise. Cole Rafferty and the Everman crew handle every call the same way: tell you what’s wrong, tell you what it costs, and fix it right the first time.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Everman Customers Say
"Fair price and no pushing a whole new gate when all I needed was a new motor capacitor."
- Shirley A."The vetted tech thing was important since our gate protects the whole property. Careful, polite, and walked me through every safety sensor."
- Russell W."Swing gate wouldn't latch after the hinge sagged. He re-hung it, adjusted the hinge pins, and fixed the latch. Quoted before starting."
- Annette R.