Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Aldine
Gate repair in Aldine usually runs between $180 and $1,400 depending on whether we’re fixing a hinge post, replacing a control board, or retrofitting a submerged operator. Most repairs are completed in a single visit, and we carry parts for LiftMaster, FAAC, BFT, Linear, and Viking operators on our trucks so we’re not driving back and forth across the Hardy Toll Road corridor. If your gate won’t open after the last bayou flood, or it’s sagging badly off its hinges, call (828) 426-7081 and we’ll give you a written price before any work starts.
We know Aldine’s gate stock better than most because we see it every week. The Aldine area has a dense mix of 1960s ranch homes with aftermarket driveway gates and commercial yards with heavy-duty slide gates that run daily semi traffic. Those are two very different repair problems. Our Gate Repair team handles both, and we’ll tell you which one you have before we touch a single bolt.
Why Warden Gate Repair Is Aldine’s Preferred Gate Repair Company
Most Aldine homeowners didn’t buy a house with a gate. They added one later, often bolting a steel or iron gate onto the original wood fence posts from a 1970s ranch home. Those posts were never engineered for gate loads. That’s why the first call we get from Aldine neighborhoods off Aldine-Bender Road and the streets around Eisenhower High School is almost always about the post leaning or the hinge pulling out, not the gate panel itself.
Our repair approach starts with the post and the footing, because in Aldine that’s usually the real problem. Black clay soil expands and contracts through every wet-dry cycle, and the soil here doesn’t just shift a little. It heaves. Posts move. Gates rack. Hinges pull screws loose. We rebuild the footing or replace the post before we hang or realign the gate, because any repair done on top of a moving post is just a temporary fix.
You’ll know who’s coming before we arrive. Every Warden technician is background-checked, identity-verified, and photo-badged under our Threshold Standard. We send you the tech’s name and photo before the visit, and they’ll show the same photo ID at your door. No anonymous vehicles, no strangers at the gate.
Cole Rafferty leads our repair operations, and the standard he set is simple: a written price before any work starts, a written guarantee on every repair, and a 365-Day Done Right Promise. If our repair fails within a year, the return visit is free. That promise is in writing on every job we do in Aldine.
Iron Gate Repair in Aldine
Iron gate repair in Aldine typically runs $250 to $950 for hinge replacement, post repair, weld repair, and realignment work. The first thing we check on any iron gate in Aldine is the hinge post, not the gate itself. Iron gates are heavy, and when they’re hung on a post set in shallow concrete or a post that’s been heaved by black clay soil, the hinges pull out or the post leans until the gate drags. We see this constantly in the residential streets between Aldine Mail Route Road and the Hardy Toll Road.
Hinge Replacement and Weld Repair
When a wrought-iron gate sags past the point of adjustment, the hinges usually need to be cut off and rewelded or replaced, and the post reset. We do both. A broken weld or a rusted hinge on a 300-pound iron gate isn’t a cosmetic issue, it’s a failure waiting to drop the gate on a car or a person.
Rust and Corrosion Treatment
Aldine’s humidity and flood exposure means iron gates here rust faster than the national average, especially near Greens Bayou. We grind back rust, repair the metal, and apply a rust-inhibiting primer. If the corrosion has compromised the gate’s structural integrity, we’ll tell you honestly whether repair or replacement makes more financial sense.
Sliding Gate Repair in Aldine
Sliding gate repair in Aldine typically costs $300 to $1,400, with commercial slide gates on concrete-set posts running toward the higher end. Sliding gates here fall into two categories: residential roll gates on older ranch properties, and heavy commercial slide gates at the trucking yards and distribution warehouses lining the Hardy Toll Road and US-59 corridors. The commercial work is different. A 40-foot steel slide gate that cycles 300 times a day for semi-truck traffic wears out rack and pinion gears, rollers, and track hardware at a rate residential gates never see.
Track, Roller, and Rack Repair
When a slide gate starts jerking or making a grinding noise, the problem is usually the track or the rack gear. On Aldine’s commercial yards we routinely find track sag caused by improper header installation on legacy gates, which then wears out the rack teeth and the pinion gear together. We replace the worn components and correct the header so the track doesn’t sag again.
Operator and Motor Replacement
The operator is the box that slides your gate automatically. On older Aldine slide gates, operators are often obsolete LiftMaster or Linear units. If the control board is corroded and the motor gear is seized, we’ll tell you straight: replacement with a new, elevated, waterproofed unit is the cheaper long-term answer. We’ll give you the written price for both repair and replacement and let you decide.
Trusted Brands We Service in Aldine
We’re factory-trained on nine gate and opener brands, and in Aldine that matters because local stock matters. We keep parts for FAAC, BFT, Linear, and Viking operators, plus LiftMaster gear, on hand for the specific failure patterns we see in this area. That means on a corroded FAAC board or a seized Viking motor gear, we’re not ordering parts and hoping they arrive by Friday. We’re fixing your gate the same visit. For Aldine commercial customers, that’s the difference between a yard that runs and a yard that sits idle.
Common Gate Repair Problems We See in Aldine Homes
- Post lean from soil heave. The black clay under Aldine expands and contracts hard with rainfall, and posts set in unengineered footings move. The gate starts dragging on the latch side, or the hinges pull out of the post. The fix starts at the post footing, not the gate.
- Corroded operators near Greens Bayou. Homes in Aldine’s flood zones see standing water inside the operator housing. Motor gears seize, logic boards corrode, and the operator stops responding. We routinely replace these with elevated, waterproofed units.
- Obsolete control boards on pre-UL 325 operators. Older gates lack working safety photocells and entrapment protection. The board is obsolete and the gate is dangerous. We’ll retrofit what’s retrofittable and tell you honestly when it’s not.
- Worn rack and pinion on commercial slide gates. The slide gates at Aldine’s trucking yards and warehouses along the Hardy Toll Road see constant use. When the rack teeth wear down, the gate grinds and jerks. We replace the rack, the pinion, or both, and correct the header if it’s sagging.
Pricing for Gate Repair in Aldine, TX
Here’s what you can expect to pay in the Aldine market. Hinge replacement on a residential iron gate: $250 to $550. Weld repairs: $150 to $400 depending on the extent. Post reset or re-footing: $400 to $900. Operator replacement including a new waterproofed unit: $750 to $1,400. Slide gate rack and pinion replacement: $500 to $1,200. A service call to diagnose the problem runs $89, and that amount is credited toward the repair if you proceed. The written price covers everything. We don’t add surprise line items at the end. Call (828) 426-7081 for a free phone estimate and an exact written quote before any work begins.
We Also Serve Cities Near Aldine
Warden Gate Repair serves Aldine and the surrounding metro from our Houston-area dispatch. If you’re in Gate Repair in Aldine‘s neighboring communities, we also cover Houston, San Antonio, Dallas, and Fort Worth, with the same upfront written pricing and the same 365-Day Done Right Promise on every job.
Serving Aldine, TX - Our Local Coverage Area
We’re based in the Aldine area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Aldine
It’s almost always the post. The black clay soil under Aldine heaves when it takes on water, and posts that were set in shallow or undersized footings shift with the soil. The gate panel itself rarely bends; the post moves and makes the gate drag. We’ll inspect the footing, reset or re-foot the post if needed, and let you know what the gate needs after that. Call (828) 426-7081 for an exact diagnosis.
Usually not, and we’ll be straight with you about it. Once standing water gets into the motor housing, the gears corrode and the logic board fails, often within weeks. We see this constantly in Aldine neighborhoods near Greens Bayou. The cheaper long-term fix is a new elevated, waterproofed operator. We’ll give you the written price for both options before you decide.
The giveaways on a legacy gate are an obvious one: no working photocell or entrapment sensor, or a control board so old it can’t support one. Gates installed before UL 325 safety requirements came into standard practice often have no reversing function. In Aldine, where many operators date from the 1980s and 1990s, this is common. We’ll assess the board and tell you if it can be retrofitted or if replacement is required for safety.
Either the header over the track has sagged out of position and is pulling the rack out of line, or the rack and pinion teeth have worn unevenly, or both. On a commercial yard that cycles heavy gate traffic every day, rack wear compounds quickly once the alignment goes. We’ll correct the header or replace the worn hardware, and give you the written price before we start.
If the keypad shows no response at all, it’s usually the keypad itself or the low-voltage wiring to it, especially after a storm when water gets into the connections. If the keypad lights up but won’t trigger the operator, the problem is more likely the board. We troubleshoot both. A keypad replacement in Aldine usually runs $150 to $350, and a board replacement starts around $400. Call (828) 426-7081 and we’ll pinpoint it in one visit.
Written by Cole Rafferty, Owner at Warden Gate Repair, serving Aldine and the surrounding Harris County area.