Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Kirby, TX
Warden Gate Repair is the gate company Kirby property owners call when a sliding gate drags off its track along FM 78 or a 1960s driveway gate won’t latch after a hard rain. We’re a gate-and-opener specialist, not a general contractor, which matters here because Kirby’s mix of light-industrial perimeter gates and older ranch-style homes means most calls need commercial-grade operator work, corrosion repair, or post re-alignment in shifting clay soil. You’ll get a written price before any work begins, and a technician whose name and photo are sent to you before arrival. Call (828) 426-7081 for a free estimate.
Why Kirby Homes Are Different
Kirby sits almost entirely inside San Antonio’s eastern boundary, but it doesn’t act like a typical Bexar County suburb. The FM 78 corridor that cuts through the city is lined with auto shops, warehouses, and small commercial yards, and a lot of those properties run heavy rolling or sliding gates across concrete aprons. That means a Kirby gate tech has to know commercial operators and track systems as fluently as residential swing gates. A residential-only shop would be out of its depth on half the jobs here.
The homes tell a different story. Most were built between the 1950s and 1970s, modest ranch houses with chain-link or basic ornamental iron driveway gates. Those gates often still run original tubular steel hardware that has been corroding for fifty or sixty years. When that hardware fails, you can’t simply order a matching replacement off a shelf. Fabrication or full gate replacement is common, and we quote that work the same way we quote a simple latch repair: a written number, before anything starts.
Bexar County’s expansive black clay is the quiet villain on many Kirby service calls. The soil swells after rain and shrinks during drought, and over thirty or forty years that cycle pushes gate posts out of plumb. A gate that worked fine in March will drag or refuse to latch by July. We re-align posts, shim hinges, and re-set operator limits on this exact failure all over Kirby.
Our Main Kirby Services
Most Kirby calls fall into three buckets: a gate that won’t open or close properly, an electric opener that quit, or a motor that runs but doesn’t move the gate. Each has its own page below.
Gate Repair in Kirby
Gate repair in Kirby usually means one of two things: a residential swing gate on a 1960s ranch home that has sagged or corroded, or a commercial sliding gate along FM 78 that has jumped its track or started dragging on settled concrete. On the residential side, we often replace failed hinges, cut out rotted posts at the base, and weld fresh steel where the old tubing has thinned. On the commercial side, we carry roller hardware and track shims specifically because cracked concrete pads on that corridor are so common. Every repair gets a written price first.
Electric Gate Repair in Kirby
Electric gate repair in Kirby covers the full powered system: keypads, loop detectors, photo eyes, safety edges, and the wiring between them. After a heavy rain, we see a spike in faulted safety edges and misaligned photo eyes on both residential and commercial gates, often because the clay soil has shifted a post just enough to break the sensing beam. We trace the circuit, identify the failed component, and replace it with the correct part for your brand. The written quote covers the diagnosis and the fix; nothing gets added on at the end.
Gate Motor Repair in Kirby
Gate motor repair in Kirby means the motor (the box that slides or swings your gate automatically) runs constantly, hums without moving, or won’t respond at all. On older residential properties, the original motor is often a brand that hasn’t been made in years, and the right call is usually a modern replacement with matching capacity for the gate’s weight. On FM 78 commercial gates, the motors are larger and often paired with loop detectors tied into traffic flow. We service Linear, Viking, Ghost Controls, and DoorKing motors, and the diagnostic comes with a flat written quote before any repair work begins.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Kirby
We’re factory-trained on nine gate and opener brands, and in Kirby we most often work on Linear, Viking, Ghost Controls, and DoorKing equipment. Common parts for those brands are stocked on our service vehicles, so most repairs don’t wait on a parts order. See our brands for the full authorized service list.
Pricing for Gate Company in Kirby, TX
| Service | Typical range in Kirby |
|---|---|
| Gate repair diagnostic (with written quote) | $49 – $125 |
| Sliding gate off track (commercial, FM 78 corridor) | $180 – $420 |
| Swing gate post re-alignment | $150 – $350 |
| Hinge replacement (ornamental iron or chain-link) | $95 – $240 |
| Latch replacement or re-strike | $75 – $180 |
| Gate motor replacement (residential swing) | $450 – $950 |
| Electric gate wiring repair | $120 – $300 |
| Safety edge replacement | $85 – $200 |
| Full gate replacement (residential, simple design) | $900 – $2,800 |
Two things push Kirby prices toward the upper end of those ranges. One is the clay soil: a post that has shifted two inches out of plumb takes more labor to re-set than a simple hinge swap. The other is fabricating replacement steel for gates built in the 1960s, because the original sections usually can’t be sourced. Whatever the job, your written price is set before we start, and it doesn’t change at the end.
Neighborhoods We Serve in Kirby
We cover the entire Kirby city limits, from the residential blocks west of Ackerman Road to the industrial yards along FM 78 and everything just off I-10 on the city’s north edge. Typical response time for Kirby service calls is same-day or next-morning, depending on call volume.
- Kirby city center, including the blocks around FM 78
- Residential streets north of Binz-Engleman Road
- Areas along Ackerman Road and Gibbs Sprawl
- Commercial and industrial lots off Loop 410 near the Kirby boundary
- Homes near Kirby Middle School and Hopkins Elementary
Service Area – Cities Near Kirby
Kirby sits inside the San Antonio metro, and while our crews serve Kirby daily, we also take gate repair calls across the wider region. If your property is in Houston, TX, San Antonio, FL, Dallas, TX, or Fort Worth, TX, one of our regional teams can help with the same written-price guarantee.
Serving Kirby, TX - Our Local Coverage Area
We’re based in the Kirby area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Kirby
Most Kirby calls are scheduled same-day or next-morning. Commercial gate failures along FM 78 get prioritized because a stuck rolling gate can shut down a whole business entrance. Live phone coverage runs 24/7, so a real person answers when you call (828) 426-7081, day or night.
For most residential gate repairs and replacements, no. Kirby does not require a city permit for a like-for-like gate swap on an existing driveway. If the job involves new electrical work for an opener that was never powered before, we’ll flag whether the wiring portion needs any city sign-off before we quote it.
We cover the full Kirby city limits, including the industrial corridor along FM 78 and the residential streets south of I-10. Since Kirby is nearly surrounded by San Antonio, we also handle gate work on properties right at the city line. Scheduling for Kirby is coordinated from our San Antonio office, and crews serve the Kirby area locally.
If your gate is sagging, dragging, or refusing to open in Kirby, call (828) 426-7081 now. You’ll speak to a live person, get a written price before any work starts, and know exactly who is coming to your gate before they arrive.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Kirby Customers Say
"Fair price and no pushing a whole new gate when all I needed was a new motor capacitor."
- Shirley A."The vetted tech thing was important since our gate protects the whole property. Careful, polite, and walked me through every safety sensor."
- Russell W."Swing gate wouldn't latch after the hinge sagged. He re-hung it, adjusted the hinge pins, and fixed the latch. Quoted before starting."
- Annette R.